Last Updated 02/11/10
 
 
Sensors
 
 
 

Sensors

   Sensors from RLC come pre-wired with a connector attached. Analog sensors use a 4-pin connector, Digital Inputs use a 3-pin connector, and Digital Outputs use a 2-pin connector. Sensor drawings are available under technical support and show you how to quickly connect the sensor to the wiring harness.

   Pre-configured wiring harnesses for the Micro Pod Lite are available from RLC. Each channel on the wiring harness is pre-measured and has the mating connectors already attached so there is no work for you to do. Select from either open wheel, closed wheel, or go kart configurations (fits most vehicles). Now all you have to do is install the harness in your car and snap it into the sensors.

   Listed below are the different sensors that RLC has for sale.

(PS-1000-5V)
Brake Pressure Sensor
(1000 PSI)

For a sensor drawing on how to properly hook up this sensor to the RLC harness click here.

$199.00

(PS-2000-12V)
Brake Pressure Sensor
(2000 PSI)

For a sensor drawing on how to properly hook up this sensor to the RLC harness click here.

$229.00

(Part# PS-100-12V)
Pressure Sensor
(1-100 PSI) (Oil and Fuel) (12V, High Performance)

For a sensor drawing on how to properly hook up this sensor to the RLC harness click here.

$159.00

(TS-300F-Fluid)
Temperature Sensor
(300 F) (Oil and Water)

For a sensor drawing on how to properly hook up this sensor to the RLC harness click here.

$59.95

(TS-300F-Air)
Ambient Air Temperature Sensor
(300 F)

For a sensor drawing on how to properly hook up this sensor to the RLC harness click here.

$59.95

(ITS-RLC-SPK)
Tachometer Sensor (Spark Plug Wire System)

Sensor can be used if there is no clean digital tach signal available on the vehicle. Wraps directly around the spark plug wire. Ideal for go kart applications.

For a sensor drawing on how to properly hook up this sensor to the RLC harness click here.

 

$59.95

(ITS-8918)
Tachometer Sensor (Coil Over System)

Sensor connects to the primary side of coil to get a tach signal. Can be used with a coil over system by attaching it to the wire that fires the coil on a coil over system.

For a sensor drawing on how to properly hook up this sensor to the RLC harness click here.

$109.00

(EGT-Kit)
EGT Sensor Kit
(Amplifier & Thermo Probe K-Type)
EGT amplifier with thermocouple probe. Comes with mounting bungs. Plugs directly into harness.

 

$249.00

(CHT-Kit)
Cylinder Head Temperature Sensor Kit
(Amplifier & Cylinder Head Temperature Sensor)
EGT amplifier with cylinder head temperature sensor. Plugs directly into harness.

Available in a 12 mm and 14 mm size.

 

$249.00

(EGT-AMP)
EGT Sensor
(Amplifier Only)
Replacement EGT amplifier must be used with thermocouple probe. Plugs directly into harness.

 

$160.00

(Thermo-Probe-K)
Thermocouple Probe (K-Type)
(Probe Only)
Replacement thermocouple probe must be used with EGT amplifier. Comes with probe and mounting bungs. Plugs directly into harness.

For a sensor drawing on how to properly hook up this sensor to the RLC harness click here.

$109.00

(CHT-Xmm)
Cylinder Head Temp Sensor
(Sensor Only)
Replacement cylinder head temperature sensor must be used with EGT amplifier. Plugs directly into harness.
Available in a 12 mm and 14 mm size.

For a sensor drawing on how to properly hook up this sensor to the RLC harness click here.

$109.00

(SS-1000)
Wheel Speed/RPM Sensor

Magnetic digital sensor, comes with magnet. Sensor can be used as a wheel speed sensor, RPM sensor, or driveline speed sensor.

For a sensor drawing on how to properly hook up this sensor to the RLC harness click here.

$129.00

Linear Position Sensors
Linear position sensors can be used for steering, throttle, or shocks. Available in four different sizes: 50mm (LPS-050)
100mm (LPS-100)
150mm (LPS-150)
200mm (LPS-200)

For a sensor drawing on how to properly hook up this sensor to the RLC harness click here.

$250.00
$250.00

$280.00
$280.00


(SPS-12)
String Potentiometer
- 12in.
String potentiometer sensor can be used for steering or throttle. Available in sizes up to 50 inches.

For a sensor drawing on how to properly hook up this sensor to the RLC harness click here.

$290.00

(Relay-10A)
Relay for Digital Output - 10 Amp

Connect for fans, fire extinguisher, or warning lights. Each relay provides the user with a normally open or normally closed connection so you can connect to anything.

For a sensor drawing on how to properly hook up this sensor to the RLC harness click here.

$54.95

(Relay-30A)
Relay for Digital Output - 30 Amp

Connect for fans, fire extinguisher, or warning lights. Each relay provides the user with a normally open or normally closed connection so you can connect to anything.

For a sensor drawing on how to properly hook up this sensor to the RLC harness click here.

$59.95

Lambda/Oxygen Sensor (Wideband)
Comes with sensor, amplifier, and mounting bungs
.

For a sensor drawing on how to properly hook up this sensor to the RLC harness click here.

$499.00

Mating Connector Kit

The mating connector kit is used to connect a sensor to a standard wiring harness. Kit includes mating connector, pins, and shrink tubing. Please check our Tech Support for sensor drawings and how to connect the sensors properly.
2-pin connector (digital output)
3-pin connector (digital input)

4-pin connector (analog input)
6-pin connector (power, CAN)








$10.00
$14.00

$17.00
$26.00
Data Acquisition Channel Expander
Instantly add additional analog and digital channels or OBD-II connectivity to your Micro Pod dash by plugging in the DACX. The expander can be used to connect to any analog sensor. Multiple expanders can be added the the Micro Pod unit. All additional analog and digital inputs are logged.
DACX 220
- 2 Analog Inputs, 2 Digital Inputs, 0 Digital Output
DACX 421

- 4 Analog Inputs, 2 Digital Inputs, 1 Digital Output
DACX 822
- 8 Analog Inputs, 2 Digital Inputs, 2 Digital Outputs

DACX 221-OBD-II
- OBD-II cable, 2 Analog Inputs, 2 Digital Inputs, 1 Digital Output

 

 

 

$395.00

$695.00

$1,095.00

$495.00

 
 
 
   
 
 
Copyright Notice. All materials copyright © 2010, R.L.C. Enterprises, Inc., all rights reserved.
XScale is a Trademark of Intel Corp. Windows and Microsoft are Trademarks of Microsoft Corp.
Racing Made Easy is a Trademark of R.L.C. Enterprises, Inc.
Micro Pod and Track Commander are Trademarks of R.L.C. Enterprises, Inc.
R.L.C. Enterprises Reserves The Right To Change Specifications Without Notice.
To View Our Privacy Policy,Click Here.
To View Our Terms and Conditions,Click Here.
Chase Commander   Micro Pod Series    Pro Series    K Pod  DACX   Pricing
Race Analysis Software   Track Mapping   Lap Timing   Sensors   Technical Information   Site Map   FAQs   Contact Us